Tue. May 17th, 2022

There are two ways to embroider clothes by hand or by using an embroidery machine. that much best embroidery machine Available in the market to help you do this perfectly. If you’re looking for the perfect way to design needle punch embroidery, you’ve come to the right place. Stay in touch with us to learn how to do this.

What is Needle Punch Embroidery?

Needle punching is a type of embroidery in which a (hollow) punching needle is used to pierce a thread or thread into the fabric, the needle is pulled out of the fabric, and a loop of thread is left on the opposite side of the fabric. This is the most traditional embroidery design method that has been around for 1 million years. This technique allows you to create long-lasting designs that will catch the eye of everyone who sees them.

Step-by-Step Tutorial on Needle Punch Embroidery

To help you understand this process more accurately, we will help you learn the smallest details with a step-by-step approach. Follow the steps below to do this perfectly.

1. Materials needed

  1. punch needle
  2. Embroidery hoop or frame
  3. Embroidery floss or yarn
  4. Punch Needle Fabric
  5. punch needle pattern
  6. Tracing pencil or carbon paper
  7. Punch Needle Threading
  8. embroidery scissors

2. Fabric Pattern Tracking

Place the pattern drawn on paper on a flat, hard surface. Then, take the fabric on which you want to perform punch needle embroidery. Place the fabric on the paper of the design pattern and attach the removable tape on both sides to keep it from moving while marking the fabric. Then trace the pattern with a tracing pen or calcium pencil. You should use a color that contrasts with the fabric.

3. Prepare the embroidery hoop

For best results on punch needle projects, the fabric hoop should be very tight. The drum must be tightened, and a smaller embroidery hoop can be used to tighten the fabric more easily. For that purpose you need to put the punch fabric inside the inner embroidery hoop. Then place the outer loop of the embroidery hoop on top of the punch fabric. Then tighten the drum using brass screws. Tighten it perfectly using a screwdriver.

4. Thread the Punch Needle

The threader must be inserted at the long end of the needle at this stage. Enter the side of the needle at the sharp end to be punctured by the punch cloth. Thread the metal threader coming from the back of the punch needle. Then the needle threader must be pulled from the front of the punch needle to the tip of the needle. Now we need to thread through the needle hole (the needle hole). First you need to bring the threader into the needle hole and then insert the thread into the needle. Then take out the threader. Be careful while performing this operation as the thread may break easily if the thread is too coarse for the needle.

5. Poke a needle into the fabric

First you need to push the puncture needle straight into the fabric until it stops. The needle hole, the part where the thread comes out when advancing, should be behind the needle. The needle should then be raised slowly onto the fabric surface until the tip is correct. Do not raise the needle too high, as raising the needle too high may cause the loop to loosen or pull. So, depending on the width of the needle, push the tip of the needle closer to the fabric.

Now repeat this until you reach the corner. You should then stop with the needle in the down position, rotate the hoop, and continue punching along the new line. This means you will always punch right to left and left to right. When the thread is finished, push the needle toward the loop of the fabric, pull out the needle, and cut the thread to the height of the loop.

When you’re done with a specific color and want to add a new color of thread, trim the start and end of the thread. Using the embroidery needle, bring the end of the thread to the back of the fabric. If the end of the thread is too short for the embroidery needle, it must be done manually. To see which loop the thread is tied to, check the thread by gently pulling it with your hand while looking at the loop part of the fabric. Then pull the loop gently to bring the end of the thread to the back of the fabric. Cut the end of the thread at the same height as the rest of the loop. The loop must be carefully pushed and pulled into position.

6. Finish

After completing the embroidery design using the needle punch method, you need to cut off the extra thread that looks messy. This will help give your design a neat and clean look.

conclusion

This is to perform needle punch embroidery using a step-by-step procedure. I hope this article was helpful and hope you can design needlepunch embroidery with ease. If you run into any problems while doing this, please post a comment and let us know. We will provide you with the best solution according to your problem. Keep in touch for more study guides like this one.

FAQ (Frequently Asked Questions)

Q 1: Is punch needle embroidery easy?

answer: Punch needles are a unique embroidery technique that both beginners and experienced crafters will love and easily perform for their needs. Once you learn the basic techniques, you can create any type of project, be it wall hangings, pillows or rugs.

Q 2: Is the punch needle the same as embroidery?

answer: The difference is the type of needle you use. More traditional embroidery uses fine needles small enough to fit between your thumb and index finger. However, the punch needle is much larger and features a hollow needle attached to the handle.

Q 3: Can the punch needle embroidery be washed?

answer: Yes, punch needle embroidery can be washed to give it a clean and fresh look.

By admin

Leave a Reply

Your email address will not be published.